The inner wall of the ventilation pipe is smooth, the resistance is small, the ventilation loss is small, the energy consumption is low, the operation cost is saved, the air tightness and sealing are good, and the pressure and compressive strength are high.

　　不锈钢管的设备主要是为了让它通风和通风功能的使用,为了达到这个目的,需要选择一些好的材料初规划设备进行处理,并结合这些因素和特点的总结和分析,为了更好地展示其性能。

　　The equipment of stainless steel pipe is mainly for its ventilation and use of ventilation function. In order to achieve this purpose, it is necessary to select some good materials for preliminary planning equipment for treatment, and combine the summary and analysis of these factors and characteristics, in order to better show its performance.

　　不锈钢风道保温材料应平铺，法兰保温材料与风道本身选用相同的保温材料，风道与法兰间距应在7mm左右，并保证两个方向之间的接触。

　　The insulation material of stainless steel air duct shall be laid horizontally. The same insulation material shall be selected for the flange insulation material and the air duct itself. The distance between the air duct and the flange shall be about 7mm, and the contact between the two directions shall be ensured.

　　在施工过程中，还要注意施工进度和总工期，这也是一个非常重要的内容。只有充分掌握这一部分，我们才能对这个项目和其他部分有一个很好的了解。我们需要熟悉管道加工的各个方面，这样我们才能更好地操作。

　　In the process of construction, we should pay attention to the construction progress and the total construction period, which is also a very important content. Only by fully mastering this part can we have a good understanding of this project and other parts. We need to be familiar with all aspects of pipe processing so that we can operate better.

　　风口表面光滑、色彩和谐、安装方法和效果是合理的,柔软的验收应同意规划标准,操作应该是强大的,自然的,风扇,风机盘管,有必要加强有用,如原材料和绝缘层的厚度应该满意的规划要求,外观应整洁,无裂纹,涂层的不锈钢管应该是优异的附着力,厚度和厚度不应脱落。

　　The surface of the tuyere is smooth, the color is harmonious, the installation method and effect are reasonable, the soft acceptance should agree with the planning standard, the operation should be strong and natural, the fan, fan coil, it is necessary to strengthen the useful, such as the thickness of the raw materials and insulation layer should meet the planning requirements, the appearance should be clean and free of cracks, the coated stainless steel pipe should be excellent adhesion, the thickness and thickness should not fall off.

　　不锈钢焊接管道是现在很常见的设备，它的加固实际上是规定和要求的，你知道吗?以下是不锈钢焊管的生产厂家。

　　Stainless steel welded pipe is a very common equipment now, its reinforcement is actually specified and required, do you know? The following is the manufacturer of stainless steel welded pipe.

　　1. 如果使用管道支架，支撑点与管道边缘或法兰之间的间距应均匀，且其值不应大于950毫米。

　　1. If a pipe support is used, the distance between the support point and the edge or flange of the pipe shall be uniform and the value shall not be greater than 950mm.

　　2. 补强或补强时，补强布置要规范，补强间距要均匀。另外，对于板材表面，不应出现明显的变形等。

　　2. For reinforcement or reinforcement, the reinforcement arrangement shall be standardized and the reinforcement spacing shall be uniform. In addition, there should be no obvious deformation on the plate surface.

　　3.焊接管道的加固应采用钢筋、立筋、角钢、扁钢、钢筋、管架等，可根据实际情况和需要进行选择。

　　3. The reinforcement of welded pipeline shall adopt reinforcement, vertical reinforcement, angle steel, flat steel, reinforcement, pipe support, etc., which can be selected according to the actual situation and needs.

　　4. 使用角钢或钢筋时，还应整齐、均匀、对称布置。高度不应大于法兰宽度。

　　4. When angle steel or reinforcement is used, it shall be arranged orderly, evenly and symmetrically. The height shall not be greater than the flange width.