当在地面预组装之后将镀锌空气管道安装在头上时预组装长度的限制是为了防止由于镀锌空气管道的自重引起的弯曲导致的部件界面的破坏。

The limitation on the length of pre assembly when installing galvanized air pipes on the head after pre assembly on the ground is to prevent damage to component interfaces caused by bending due to the weight of the galvanized air pipes.

轴通过镀锌风管垂直安装由于空间小不便于以后维护所以镀锌风管一般采用夹套角钢法兰连接增加连接点的坚固性和强度并将法兰变成一个“井”形状吊架直接悬挂在凸耳上的角钢法兰上无需额外支撑。

The axis is vertically installed through galvanized air ducts. Due to the small space and inconvenient maintenance in the future, galvanized air ducts are generally connected by jacket angle steel flanges to increase the firmness and strength of the connection points and transform the flange into a "well" shape. The hanger is directly suspended on the angle steel flange on the lug without additional support.

非法兰连接玻璃纤维复合板镀锌风管垂直安装支撑件的生产和安装方法。

Production and installation method of vertical installation support components for non flange connected glass fiber composite sheet galvanized air ducts.

在镀锌风管的榫眼接头上涂上粘合剂以提高接头的强度。

Apply adhesive to the mortise and tenon joints of galvanized air ducts to improve the strength of the joints.

应采取保护措施防止在运输过程中损坏镀锌空气管道。

Protective measures should be taken to prevent damage to galvanized air pipes during transportation.

玻璃纤维复合板镀锌风管端口用于切割表面装配前法兰连接器应用胶带或胶水切割表面密封以防止玻璃纤维暴露和飞扬。

The galvanized air duct end of fiberglass composite plate is used to cut the surface. Before assembly, the flange connector should be sealed with tape or glue to cut the surface to prevent exposure and flying of fiberglass.

强度高强度小开孔性好锤形装置长使用的原材料均采用弯辊生产3在外面和里面当听到补语时会有二次撕裂。可现场制作可切割可钻孔设备简单省工省时85个。镀锌风管设备完工后不得进行防护。减少保护基金11号。镜锌板风管水平装置长边直径或底寸小于或等于400mm间距不大于4m；大于400mm不宜大于3m镀锌风管支管、吊架间距可延长至5m和3.75m；钢板法兰镀锌框架间距不大于3m。

The hammer shaped device has high strength, small opening, and good performance. The raw materials used for long-term use are all produced by bending rollers. When the complement is heard on the outside and inside, there will be secondary tearing. The on-site production of cutting and drilling equipment is simple, labor-saving, and time-saving with 85 pieces. Galvanized air duct equipment shall not be protected after completion. Reduce Protection Fund No. 11. The long side diameter or bottom dimension of the mirror zinc plate air duct horizontal device is less than or equal to 400mm, and the spacing is not more than 4m; For galvanized air duct branches and hangers larger than 400mm and not larger than 3m, the spacing can be extended to 5m and 3.75m; The spacing between galvanized steel plate flanges and frames shall not exceed 3m.

红外线管道支吊架应强度和强度的选择模式和标准符合gb atls和标准。特种镀锌板风管支吊架风口、阀门、检修门及自控机构与风口或堵头的间距鑫{痧机加工后的吊杆应螺纹完好光亮。每个辅助支撑器和吊架应力可用于振动冲击支吊架的拆卸或吊装

The selection mode and standards for the strength of infrared pipeline supports and hangers should comply with GB ATLS and standards. The spacing between the air vent, valve, maintenance door, and self-control mechanism of the special galvanized sheet air duct support and hanger, as well as the air vent or plug, should be intact and bright after machining. The stress of each auxiliary support and hanger can be used for the disassembly or hoisting of vibration impact support and hanger