通风管道效果很大，为人们的健康保驾护航，通风管道成为了人们日常日子中不能短少的一部分。济南通风管道加工的技能现在越来越好，那么如何避免的通风管道在运用中会呈现的破损问题呢？

Ventilation ducts have a great effect and provide protection for people's health. Ventilation ducts have become an indispensable part of people's daily lives. The skills in processing ventilation ducts in Jinan are getting better and better, so how can we avoid the problem of damage that may occur in the use of ventilation ducts?

1、通风管道加工的进程中应该尽量避免呈现纵向接缝，但是不能呈现横向接缝。而且通风管道的咬口缝和四角的缝隙处，需求依照规划洁净等级要求，然后还要选用密封胶将其堵严。其他通风管道板材的联接缝的密封面应该设在通风管道壁的正压侧。

1. During the processing of ventilation ducts, longitudinal joints should be avoided as much as possible, but transverse joints should not be present. Moreover, the bite seams and corners of the ventilation ducts need to be sealed tightly with sealant according to the cleanliness level requirements of the planning. The sealing surface of the joint of other ventilation duct panels should be set on the positive pressure side of the ventilation duct wall.

2、加工的时分，不能在通风管道内部设置加固框或许加固筋，因为这样关于通风管道的质量会构成影响。

2. During processing, reinforcement frames or ribs should not be installed inside the ventilation duct, as this will affect the quality of the ventilation duct.

3、通风管道加工不能选用S型插条和C型直角插条的联接办法，其他关于一些的通风管道来说，还不能选用按扣式的咬口。

3. The connection method of S-shaped inserts and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. For some other ventilation ducts, snap fit bites cannot be used.

4、通风管道制造结束之后，还要用清洗液进行清洗，只需抵达清洗规范之后，才干够及时封口。

4. After the manufacturing of the ventilation duct is completed, it needs to be cleaned with cleaning solution. Only after reaching the cleaning specifications can it be sealed in a timely manner.

5、假设是彩色涂层钢板通风管道的话，应该坚持内壁是润滑的，而且通风管道加工的进程中，还不能将涂层损坏，若是呈现损坏的部位，需求用环氧树脂涂刷在外表即可。其他通风管道加工的进程中，还要做好防腐蚀办法，不能运用抽芯铆钉，而且在通风管道零件设备的时分，这些零件都要通过镀锌处理才行。

5. If it is a color coated steel plate ventilation duct, it should be adhered to that the inner wall is lubricated, and the coating should not be damaged during the processing of the ventilation duct. If the damaged part appears, it needs to be coated with epoxy resin on the surface. In the process of processing other ventilation ducts, anti-corrosion measures should also be taken, and core pulling rivets cannot be used. Moreover, when using ventilation duct parts and equipment, these parts must be galvanized.

假设在通风设备设备时发现破损已抵达玻纤保温层时，则可将破损的当地切开下来，另选一块无缺的板材，依据切开下来的玻板规范切开好，然后在周围接口上涂上修补胶及粘胶剂，依据工艺规范连续密封，在通风设备正常作业时就要常常查看避免耽搁作业。只需正常作业的通风设备才会为人类效能，这就央求要及时查看设备能否破损。更多相关内容就来我们网站http://www.jntfgd.com咨询吧！

If it is found that the damage has reached the fiberglass insulation layer during the ventilation equipment, the damaged area can be cut off, and another intact board can be selected. The cut glass board should be cut according to the specifications, and then repair adhesive and adhesive should be applied to the surrounding interfaces. Continuous sealing should be carried out according to the process specifications. It is necessary to frequently check and avoid delaying the operation during normal operation of the ventilation equipment. Only normal ventilation equipment is required for human efficiency, which requires timely inspection of whether the equipment is damaged. For more related content, come to our website http://www.jntfgd.com Consult!